AutoSim Sensor-Simulator

SKU: 7180
Category: Sensor Simulator
Manufacturers: DITEX
Product safety information

319,00 €

incl. 19% VAT , plus

Taxing District / Country of Destination

Product cheaper elsewhere?
Available
Delivery time: 1 - 3 Workdays

Product cheaper elsewhere?

If you found our product cheaper elswhere, contact us and we'll try to beat our competitor's advertised price!

Submit request

Since its release in 2012, the AutoSim Sensor Simulator has proven extremely popular with both technicians and professional diagnosticians thanks to its user-friendly interface as well as the agreeable and reliable operation.

Eight years after the release of the original model, Ditex now presents the AutoSim Pro and with that, the second generation. Distinguished through its fully updated design and significant functional improvements and also by the fact that it is a very useful tool, the AutoSim Pro Sensor Simulator by Ditex is suited for application in both motor vehicles and lorries in a large number of work situations. This advanced sensor simulator creates an electrically equivalent system to simulate the sensors and actuators of a vehicle.

In general, the AutoSim Pro is a specialised signal generator for testing sensors, including lines and connections if installed. This way, you can determine whether a control device, a plug-in, a plug connection or a sensor is defective. This allows for an efficient error solution without having to replace parts haphazardly. A special feature of the device is the simple and intuitive operation via the function buttons. The display continuously shows the most important settings such as the current waveform, frequency, amplitude, offset, ramp time and pulse width.

Signal generator

With the most important signals: sine, square, traingle and ramps up to 20 kHz, the device is the ideal companion for experiments with components and sensors of all types as well as for analysing electric wiring circuits. You have full control of the output signal: peak-to-peak amplitude, frequency, work cycle and pulse width. A micro-controller sets the output voltage corresponding to the programmed curves in the range of 0 V to ± 12 V.

PWM

PWM generator for the dynamic control of vehicle actuators using pulse width modulation. The PWM generator function was specifically developed to control flaps, actuators, valves, injectors and smaller direct current motors. For generating a PWM signal with variable power up to 4 A.

Precise direct-current voltage source

The high-resolution direct-current voltage output function AutoSim Pro without static is the right choice when a precise direct-current voltage source is required. Its bipolar output provides up to ± 12 V with a resolution of 10 mV and a current of up to 35 mA.

Sensor-embedded presettings

Automotive sensor simulator with integrated, preset configurations for simulating of CKP Inductive, CKP Hall Effect, Lambda sensor zirconium oxide, Lambda sensor titanium dioxide and knock sensor. You can disconnect the sensor from the cable form, enter the signal into the cable form and observe the sighting telescope to determine if the PCM reacts positively.

Handheld testing device
Intuitive operation via function buttons
Extremely fast start-up
Excellent industry design
Works with both 12 V and 24 V systems
Lit up 2,4" TFT LCD 320 x 240 display for optimal visibility
Protected against polarity reversal
Low distortion factor and high signal-static-ratio for brilliant signals
Frequency range can be set from 0,1 Hz to 20 kHz
Generating PWM signals with variable power of up to 4 A
Single-wire connection PWM output
Precise direct-current voltage source
Internal micro SD card for firmware updates

Simulates the actual working conditions of most vehicle sensors
Efficient error solutions without haphazardly replacing parts
Simulates O2 sensor signals: zirconium dioxide and titanium dioxide
Checking of the basic control device functions
By controlling the output signal you can check the responsiveness and the control device operation
It can lead the control device into an "open" or " closed" loop
Activation of numerous actuators
Variable voltage output can be set from 0 to ± 12 V
Simulates inductive crank and cam sensors and hall
In both crank and cam mode you can set the number of teeth and the missing teeth

General technical specifications

Scanning rate	200 KSa/s
Settling rate	4.5 µs
Resolution	12 bit
Maximum output frequency	20 kHz
Output channels	2
Signal output	SOUT
Output line	POUT
Simultaneous operation of both outputs	Yes
Standard types of operation	Waveform, direct current, pulse
Installed vehicle presettings	Yes
High voltage PWM Control	Yes
Direct current supply	12V, 24V DC (vehicle battery)

Display

Type	TFT LCD module
Size	2.4" diagonal
Resolution	320 x 240 p
Background lighting	4chip white LED parallel
High brightness	150 cd/m2

Real time clock battery
CR2032, 210 mA/h - energy for up to three years without external supply

Important note: Because of lithium-ion battery shipping restrictions, we do not include a CR2032 lithium-ion battery in air mail post packages. When you receive the tester, you will have to buy a Li-Ion battery type CR2032 yourself and insert it into the battery holder socket inside the CarScope i-Tester. To do so, unscrew and remove four screws to open the bottom cover. We apologize for the inconvenience!

Included Memory Card
4 GB micro SDH

Signal output specifications

Output polarity	Positive and negative
Output amplitude	±10 mV ~ ±12 V (10 mV step)
Direct-current voltage output range	±10 mV ~ ±12 V (10 mV step)
Output current	± 30 mA max.
Vertical resolution	12 Bit
Waveform	Sine, square, triangle, ramp
Sine frequency range	0.1 Hz ~ 5 kHz
Ramp / triangle frequency range	0.1 Hz ~ 5 kHz
Rectangle wave frequency range	0.1 Hz ~ 20 kHz
Rectangle wave duty cycle range, 20 kHz	20% ~ 80 %, step 0.1%
Rectangle wave duty cycle range, 10 kHz	10% ~ 90 %, step 0.1%
Rectangle wave duty cycle range, up to 5 kHz	5% ~ 95 %, step 0.1%
Pulse	1 ~ 100
Pulse width	1 ms ~ 1 sec
Pulse period	2 ms ~ 5 sec

Performance specification

Output polarity	Positive
Amplitude	12 V
Max. output current	4 A continuously
Active level	"switched earth"
Output frequency range	up to 2 kHz
PWM work cycle range	1% ~ 100%
Accuracy of the work cycle setting	0.1%
Thermic cut-off	Yes
Overvoltage protection	Yes
Current limitation	Yes
Short-circuit protection	Yes

Other

Voltage supply range	10V DC to 28V DC
Current connection	Pluggable connection block 5.0mm, 2 POS
Stall current	≤160mA
Surroundings temperature	0°C ~ +35°C
Surroundings humidity	0% rF ~ 85% rF
Measurements	160 mm x 94 mm x 25 mm
Weight	500g