This new kit is intended for technicians that need to work on electric and hybrid vehicles. However, it can also easily be used for standard combustion vehicles or other machines that have been supplemented with this technology.
The kit is supported by a new assortment of executed tests which are continuously updated as soon as new systems, courses of procedures and functional errors are recognized.
The main components of the kit are 3 high current clamps, a 2 pole voltage tester, an isolation tester and a high voltage measuring probe. As in all kits, these accessories can also be used with other kits.
| Model |
PicoScope 4425A |
| Bandwidth |
20 MHz |
| Channels |
4 (galvanically separated) |
| Vertical resolution |
12 bit |
| Expanded vertical resolution |
16 bit |
| Accuracy |
DC ± 1% of the full scale |
| Sensitivity |
10 mV/div to 40 V/div |
| Input ranges (full scale) |
± 50 mV to ± 200 V in 12 ranges |
| Input impedance |
1 MOhm parallel to 24 pF |
| Input type |
Potential free, single pole plug connector PicoBNC+ |
| Input coupling |
AC/DC selectable in software |
| Input overvoltage protection |
± 250 V (DC + AC peak) |
Maximum sampling rate (single shot)
1 channel in use
2 channels in use
3 or 4 channels in use |
400 MS/s
200 MS/s
100 MS/s |
| Cache |
250 M samples shared between active channels |
| Waveform cache |
Up to 10,000 waveforms |
| Timebase ranges |
5 ns/div to 5000 s/div |
48V mild hybrid systems
- Starting and charging systems with 48V and 12V
- Battery cell measurements on 48V batteries
- Direct current charging systems
- Standard tests of combustion engines
Full & plugin hybrid systems
- Testing isolation components
- 3-phase alternatig current measuring, when possible
- Test electric motor / generator position sensor
- Direct current charging systems
- Diagnosis of the CP and PP communication line
- Standard tests of combustion engines
- Establish secured voltage-free status and restart
- Measuring the charging rate in current and voltage
Battery electric vehicles
- Establish secured voltage-free status and restart
- Testing isolation components
- Test electric motor / generator position sensor
- Direct current charging systems
- 3-phase alternatig current measuring, when possible
- Diagnosis of the CP and PP communication line
- Measuring the charging rate in current and voltage
Fuel cell vehicles
- Establish secured voltage-free status and restart
- Testing isolation components
- Test electric motor / generator position sensor
- Direct current charging systems
- 3-phase alternatig current measuring, when possible
- Diagnosis of the CP and PP communication line
- Measuring the charging rate in current and voltage
- Test air supply system
- 1x USB-2 cable 4,5 m blue
- 2x "S" hook
- 1x case
- 1x 4-channel PicoScope 4425A
- 1x multimeter probe tip (black)
- 1x multimeter probe tip (red)
- 2x small alligator clamp (black)
- 2x small alligator clamp (red)
- 1x big dolphin clamp 1000V CATIII (black)
- 1x big dolphin clamp 1000V CATIII (red)
- 4x 4 mm banana plug adapter, protected to unprotected (red)
- 1x extension adapter for standard ATC fuse
- 1x extension adapter for mini ATC fuse
- 1x differential scope probe: x20/x200 25MHz 1400V CATIII
- 1x USB 3.0 cable blue 1,8 m
- 2x battery clamp (red)
- 2x battery clamp (black)
- 1x extension adapter for JCASE fuse
- 1x extension adapter for MAXI fuse
- 1x parking sensor detector 2 m
- 1x keyless entry carrier signal detector 3 m
- 3x PicoBNC+ current clamp 2000A AC/DC
- 1x PicoBNC+ linear temperature sensor with big measuring range
- 1x PicoBNC+ (COP) ignition coil and signal sensing head
- 2x PicoBNC+ automotive 10:1 measuring line & adapter
- 1x PicoBNC+ 3 m measuring line, permanent mass, 4 mm blue
- 1x PicoBNC+ 3 m measuring line, permanent mass, 4 mm red
- 1x PicoBNC+ 3 m measuring line, permanent mass, 4 mm green
- 1x PicoBNC+ 3 m measuring line, permanent mass, 4 mm yellow
- 1x PicoBNC+ resistance measuring line
- 3x 1000V backpinning probe (black)
- 3x 1000V backpinning probe (red)
- 1x Pico 2 poligen voltage tester
- 1x Pico isolation measuring device
- 1x PicoBNC+ current clamp 60A AC/DC
There are no reviews yet.
